TITE-LOC Panels combine structural panel performance with architectural panel aesthetics. TITE-LOC Panels are corrective leveled to provide superior panel flatness. A factory-applied sealant bead is applied for additional weather resistance. (minimum panel length is 4 feet)

TITE-LOC Panels feature a 2” leg height that requires mechanical field seaming after installation. Panels have a concealed-fastener floating clip system designed to allow for thermal expansion/contraction. For further details, please contact PAC.

UL 90 Classified
TITE-LOC Panels carry a UL 90 classification over a wide variety of substrates and assemblies including 5/8” plywood, purlins, and rigid insulation in conjunction with bearing plates (UL Construction No. 90, 176, 180, 238B, 437, 449, 451, 452, 487, 616, 617). For further details, contact Petersen Aluminum Corp.

Air and Water Infiltration
TITE-LOC Panels meet the full performance requirements of the ASTM E283/1680 air infiltration test and the ASTM E331/1646 water penetration test. Please contact Petersen Aluminum Corporation for complete test results.

Materials
a) 24 ga. G-90 hot-dipped galvanized steel
b) 22 ga. G-90 hot-dipped galvanized steel
c) .032 3105-H14 aluminum
d) .040 3105-H14 aluminum

Trim
All flashing and trim will be fabricated by manufacturer or qualified fabricator. Flashing shall be PAC-CLAD aluminum (.032-.063 gauge as specified) or PAC-CLAD steel (24 ga. or 22 ga. as specified). A 20 year, non-prorated finish warranty shall be supplied covering finish performance.

Installation
TITE-LOC Panels are intended for use in architectural and structural roofing. Substrates may include 5/8” (min.) plywood, nailboard insulation or equal with an underlayment of 30# (min.) roofing felt applied horizontally from eave to ridge. Other substrates may include metal decking, purlins or rigid insulation in conjunction with bearing plates. A minimum 1/2:12 roof pitch is required. Contact Petersen for further detail assistance on projects. For Coastal applications, aluminum panels along with stainless steel clips must be used for warranty. Consult a local architect/engineer for compliance with local codes and conditions.

Tite-Loc Panels
Tite-Loc Panels are factory-formed to length and field seamed to a 90º lock. Tite-Loc panels have been designed for application on roof slopes as low as 1/2:12 pitch. As an additional labor-saver, the Tite-Loc seamer has been designed to travel both up and down slope during installation. Tite-Loc panels are available in 12”, 16” and 18" widths. Materials available include 22 and 24 gage steel; .032 and .040 aluminum.

Tite-Loc Plus Panels
Tite-Loc Plus Panels are factory-formed to length and designed to be field-seamed to 180º. The panel combines an attractive thin-rib profile with superior structural performance. Tite-Loc Plus panels are designed for application over a wide varietyof substrates in slopes as low as 1/2:12 pitch. Tite-Loc Plus panels are available in 12”, 16” and 18" widths. Materials available include 22 and 24 ga. steel; .032 and .040 aluminum.

Curved Tite-Loc Panels
Tite-Loc Panels can be curved to a minimum radius of 20’-0”. Tite-Loc curving can be done in the field or at the factory depending on the radius and length of the panel. For more details about our capabilities, please contact Petersen Aluminum Corporation.

*24 ga. and 22 ga. panels listed in bold print are UL-90 classified over solid substrate. See roof deck construction in Underwriter Laboratories roofing materials and systems directory.
Tite-Loc and Tite-Loc Plus Panels are shown with optional striations. Standard product offering is smooth.