Integral Standing Seam Panel

Integral Standing Seam Panel

  • Ideal for transition roofs
  • Herr-Voss corrective leveled
  • Stiffener beads available
  • 20-year non-prorated finish warranty
  • Maximum panel length of 45 feet

Integral Standing Seam metal roofing panels are designed for roofing applications, mansards, canopies and fascia. The one-piece design of the panels minimizes labor and allows for quick and easy installation. Integral panels are to be factory roll formed in continuous lengths. Maximum panel length is 45 feet and minimum panel length is 4 feet.


Standard on-center dimensions are 11″, 18″ and 19″, but for renovation projects or additions, on-center dimensions may be custom matched to your requirements. Neoprene panel closures are available for installation at the eave.



For roofing applications, use Petersen non-penetrating clips. Clips shall be 606l-T6 extruded aluminum, fastened on 18″ centers. Use wood-type screws in fastening clips. For fascia and mansard applications, panels should be positively fastened to the substrate.



All flashing and trim shall be fabricated by manufacturer or qualified fabricator. Flashing shall be PAC-CLAD aluminum (.032 – .063 gauge as specified) or PAC-CLAD steel (24 gauge or 22 gauge as specified). A 20-year non-pro-rated finish warranty can be supplied covering finish performance. Vinyl masking is recommended on all fabrication applications where extra handling is expected. NOTE: The strippable film must be removed immediately after installation.



Roofing Applications: PAC-CLAD Integral Standing Seam Panels shall be installed over solid decking (5/8″ plywood, nailboard insulation or equal) with an underlayment of 30# (min.) roofing felt applied horizontally from eave to ridge. Panels shall be fastened using Petersen non-penetrating clips, fastened on 18″ centers (max.). Minimum slope at 3:12 pitch. Consult a local architect/engineer for requirements of local codes and conditions.


  • 38 stocked colors (24 ga. steel)
  • 37 stocked colors (.032 aluminum)
  • Galvalume Plus available

Integral Standing Seam Installation

Snap-Clad Panel
Tite-Loc Panel
Tite-Loc Plus Panel
Tite-Loc HS Panel
Snap-On Standing Seam Panel
High Snap-On Standing Seam Panel
Snap-On Batten Panel
Redi-Roof Standing Seam Panel
Redi-Roof Batten Panel
Integral Standing Seam Panel
Integral Batten Panel
ColorGard® Snow Retention System
PAC-150 90° Single Lock
PAC-150 180° Double Lock
M-42 & M-36 Panels
7.2 Panel
1/2″ & 7/8″ Corrugated Panel
R-41 & R-36 Panels
Coil and Flat Sheet
Flashing and Trim
Custom Fabrication
Anodized Aluminum
Copper & Stainless Steel
PAC-750 Soffit
PAC-850 Soffit
Flush/Reveal Soffit
PAC-1000F Column Cover
PAC-1000C Column Cover
PAC-1000R Column Cover
PAC-2000F Column Cover
PAC-2000C Column Cover
PAC-2000R Column Cover
PAC SS Vented Eave & Intake Vent
PAC ECO Vented Fascia
PAC SS Rake Panel & Fascia
PAC SS Ridge Vents
PAC-TITE Angular Fascia
PAC-TITE WT Canted Fascia
PAC-TITE WT Extended Fascia
PAC-LOC Fascia
PAC Snap Edge Fascia
PAC Extended Snap Edge Fascia
PAC-TITE Gold Coping
PAC-Continuous Cleat Coping
Precision Series Wall Panels
Composite Wall Panels
Flush/Reveal Wall Panels