Snap-On Standing Seam Panel

Snap-On Standing Seam Panel

Features
  • Ideal for transition roofs
  • Stiffener beads available
  • Herr-Voss corrective leveled
  • 20 year non-prorated finish warranty
  • Maximum panel length of 45 feet

Snap-On Standing Seam metal roofing panels are designed for use in roofing, mansard and fascia applications. The panels are designed to be installed over a waterproofed solid substrate and a minimum 3:12 roof pitch. Snap-On Metal Panels are to be factory roll-formed in continuous lengths. Maximum panel length is 45 feet and minimum panel length is 4 feet.

 

These metal panels are ideal for specification on applications where roofing transitions are required. The simplicity of the pan design combined with corrective leveling provides superior flatness and allows for greater workability on site.

 

Trim

All flashing and trim shall be fabricated by manufacturer or qualified fabricator. Flashing shall be PAC-CLAD aluminum (.032 – .063 gauge as specified) or PAC-CLAD steel (24 gauge or 22 gauge as specified). A 20-year non-pro-rated finish warranty can be supplied covering finish performance. Vinyl masking is recommended on all fabrication applications where extra handling is expected. NOTE: The strippable film must be removed immediately after installation.

 

Curved Panels

The 1″ high Snap-On Standing Seam Roofing Panel can now be curved to a concave or convex radius, with a minimum radius of 9 ft. This panel is ideal for barrel vaults and entrance ways. Curved panels must be installed over a waterproofed solid substrate.

 

Installation

Snap-On Metal Panels shall be installed over solid decking (5/8″ plywood, nailboard insulation or equal) with an underlayment of 30# (min.) roofing felt applied horizontally from eave to ridge. Panels shall be fastened using Petersen Non-Penetrating Clips, fastening on 18″ centers (max.). Minimum slope at 3:12 pitch. Consult a local architect or engineer for requirements of local codes and conditions.

Materials:

  • 37 stocked metal colors (24 gauge steel)
  • 36 stocked metal colors (.032 aluminum)
  • Galvalume Plus available

Snap-On Standing Seam Installation

Snap-Clad Panel
Tite-Loc Panel
Tite-Loc Plus Panel
Tite-Loc HS Panel
Snap-On Standing Seam Panel
High Snap-On Standing Seam Panel
Snap-On Batten Panel
Redi-Roof Standing Seam Panel
Redi-Roof Batten Panel
Integral Standing Seam Panel
Integral Batten Panel
Edge-Loc Panel
Colorguard™ Snow Guards
M-42 & M-36 Panels
7.2 Panel
1/2″ & 7/8″ Corrugated Panel
R-41 & R-36 Panels
Flat and Coil Stock
Flashing and Trim
Custom Fabrication
Anodized Aluminum
Acrylic Aluminum
Copper & Stainless Steel
PAC-750 Soffit
PAC-850 Soffit
Flush/Reveal Soffit
PAC-1000F Column Cover
PAC-1000C Column Cover
PAC-1000R Column Cover
PAC-2000F Column Cover
PAC-2000C Column Cover
PAC-2000R Column Cover
PAC SS Vented Eave & Intake Vent
PAC ECO Vented Fascia
PAC SS Rake Panel & Fascia
PAC SS Ridge Vents
PAC-TITE Angular Fascia
PAC-TITE WT Canted Fascia
PAC-TITE WT Fascia
PAC-TITE WT Extended Fascia
PAC-LOC Fascia
PAC Snap Edge Fascia
PAC Extended Snap Edge Fascia
PAC-TITE Coping
PAC Anchor-Tite Coping
PAC-Continuous Cleat Coping
PAC Precision Series
Composite Wall Panels
Flush/Reveal Wall Panels