Flush/Reveal Wall Panels

Flush Wall Panel
Reveal Wall Panel

Flush/Reveal Wall Panels

Flush Wall Panel

Flush Wall Panel
Reveal Wall Panel
Features
  • Corrective leveled for superior flatness
  • Available with up to two stiffener beads
  • Rounded interlock leg provides improved flush fit
  • 30-year non-prorated finish warranty
  • Panel lengths up to 25’

PAC Flush panels are designed for wall, fascia and soffit applications where a flush or flat appearance is desired. A rounded interlock leg and concealed fastening system improves the flush appearance while providing additional strength. Panels are factory-formed to length to minimize field cutting. Maximum panel length is 25’ and minimum panel length is 4’.


PAC Flush panels are available in on-center dimensions designed to complement our roofing panel product line. Flush panels are available in two configurations: Flush panel and Reveal panel.

 

 

Stiffening beads

The Flush panel and Reveal panel are available with optional stiffening beads. Stiffening beads are recommended for longer panel lengths. One or two beads are available.

 

 

Installation

PAC Flush panels shall be installed over a solid substrate with appropriate 30# felt or ice and water shield, or in limited applications over framing sections. When used in a windscreen application, panels must be fastened (stitched) through side joints. Consult a local architect/engineer for requirements of local codes and conditions.

 

 

Corrective Leveling

Petersen Aluminum Flush panels are formed on precision roll-forming equipment that includes in-line Herr-Voss corrective levelers. Corrective leveling works to remove typical metal conditions including coil set, crowning and edge wave. In-line leveling capabilities allow us to work with source material that is “stillwater” flat. The result is a panel that exhibits superior flatness. Corrective leveling is available at no extra charge.

 

 

Trim

All flashing and trim shall be fabricated by manufacturer or qualified fabricator. Flashing shall be PAC-CLAD aluminum (.032 – .063 gauge as specified) or PAC-CLAD steel (24 gauge or 22 gauge as specified). A 30-year non-prorated finish warranty can be supplied covering finish performance. Vinyl masking is recommended on all fabrication applications where extra handling is expected.

Materials:

  • 38 stocked colors (24 ga. steel)
  • 15 stocked colors (22 ga. steel)
  • 36 stocked colors (.032 aluminum)
  • 20 stocked colors (.040 aluminum)
  • Galvalume Plus available
Snap-Clad Panel
Tite-Loc Panel
Tite-Loc Plus Panel
Tite-Loc HS Panel
Snap-On Standing Seam Panel
High Snap-On Standing Seam Panel
Snap-On Batten Panel
Redi-Roof Standing Seam Panel
Redi-Roof Batten Panel
ColorGard® Snow Retention System
PAC-150 90° Single Lock
PAC-150 180° Double Lock
M-42 & M-36 Panels
7.2 Panel
1/2″ & 7/8″ Corrugated Panel
R-41 & R-36 Panels
Coil and Flat Sheet
Flashing and Trim
Custom Fabrication
Anodized Aluminum
Copper & Stainless Steel
PAC-750 Soffit
PAC-850 Soffit
Flush/Reveal Soffit
PAC-1000F Column Cover
PAC-1000C Column Cover
PAC-1000R Column Cover
PAC-2000F Column Cover
PAC-2000C Column Cover
PAC-2000R Column Cover
PAC SS Vented Eave & Intake Vent
PAC ECO Vented Fascia
PAC SS Rake Panel & Fascia
PAC SS Ridge Vents
PAC-TITE Angular Fascia
PAC-TITE WT Canted Fascia
PAC-TITE WT Fascia
PAC-TITE WT Extended Fascia
PAC-LOC Fascia
PAC Snap Edge Fascia
PAC Extended Snap Edge Fascia
PAC-TITE Gold Coping
PAC-TITE Coping
PAC-Continuous Cleat Coping
Precision Series Wall Panels
Composite Wall Panels
Flush/Reveal Wall Panels