2016 - Tite-Loc Plus

Features

task_altPencil ribs (stiffening beads) are available only by request
task_alt35-year non-prorated finish warranty
task_altMaximum factory-produced panel length is 64’ (check w/factory for longer lengths)
task_altWeathertightness warranty available

Features

task_altPencil ribs (stiffening beads) are available only by request
task_alt35-year non-prorated finish warranty
task_altMaximum factory-produced panel length is 64’ (check w/factory for longer lengths)
task_altWeathertightness warranty available

Tite-Loc Plus panels combine structural panel performance with architectural panel aesthetics. Tite-Loc Plus panels are leveled to provide superior panel flatness. A factory-applied sealant bead can be applied for additional weather resistance. Maximum panel length is 64’ and minimum panel length is 4’. Consult factory for longer lengths. Note: Minimum length for panels produced in the Annapolis Junction, Md., facility is 60 inches.

Tite-Loc Plus panels feature a 2” leg height that requires mechanical field seaming after installation. Panels have a concealed-fastener floating clip system designed to allow for thermal expansion/contraction.

Trim
All flashing and trim shall be fabricated by manufacturer or qualified fabricator. Flashing shall be PAC-CLAD aluminum (.032 – .063 gauge as specified) or PAC-CLAD steel (24 gauge or 22 gauge as specified). A 35-year non-prorated finish warranty can be supplied covering finish performance. Vinyl masking is recommended on all fabrication applications where extra handling is expected.  NOTE: The strippable film must be removed immediately after installation.

Installation
Tite-Loc Plus panels are intended for use in architectural and structural roofing. Substrates may include 5/8” (min.) plywood,  nailboard insulation or equal with an underlayment of ice and water shield applied horizontally from eave to ridge. Other substrates may include metal decking, purlins or rigid insulation in conjunction with bearing plates. A minimum 1/2:12 pitch is required. Contact Petersen for further assistance with projects details.

For coastal applications, aluminum panels along with stainless steel clips must be used for finish warranty. Consult a local architect/engineer for compliance with local codes and conditions.

Tite-Loc/Tite-Loc Plus Panels
Tite-Loc and Tite-Loc Plus panels are factory-formed to length and field-seamed to a 90° lock (Tite-Loc) or a 180° lock (Tite-Loc Plus). The panels have been designed for application over a wide variety of substrates on roof slopes as low as 1/2:12 pitch. Available in 12”, 16” and 18” widths, Tite-Loc and Tite-Loc Plus panels can be produced in 22 and 24 gauge steel or .032 and .040 aluminum.

Seaming
Tite-Loc and Tite-Loc Plus panels require the use of mechanical seamers. When seaming panels on slopes greater than 6:12, caution must be exercised to prevent seamer slippage and resulting finish scratches that may void the warranty. Seamers are available along with hand crimpers and other tools through D.I. Roof Seamers, which is the only supplier of this equipment approved by Petersen Aluminum. For details and rental information Click Here.

Metal Roofing - How to install Tite-Loc Plus Standing Seam Panel

Tite-Loc Plus Smooth Panel
Smooth Panel (Standard)
zoom_in
Tite-Loc Plus with Striations
With Striations (Optional)
zoom_in
Tite-Loc Plus Striations with Pencil Ribs
Striations w/ Pencil Ribs (Optional)
zoom_in
Tite-Loc Plus Pencil Ribs
Pencil Ribs (Optional)
zoom_in
layers43 stocked colors (24 gauge steel)
layers16 stocked colors (22 gauge steel)
layers36 stocked colors (.032 aluminum)
layers22 stocked colors (.040 aluminum)
layersGalvalume Plus available

Tite-Loc Plus panels combine structural panel performance with architectural panel aesthetics. Tite-Loc Plus panels are leveled to provide superior panel flatness. A factory-applied sealant bead can be applied for additional weather resistance. Maximum panel length is 64’ and minimum panel length is 4’. Consult factory for longer lengths. Note: Minimum length for panels produced in the Annapolis Junction, Md., facility is 60 inches.

Tite-Loc Plus panels feature a 2” leg height that requires mechanical field seaming after installation. Panels have a concealed-fastener floating clip system designed to allow for thermal expansion/contraction.

Trim
All flashing and trim shall be fabricated by manufacturer or qualified fabricator. Flashing shall be PAC-CLAD aluminum (.032 – .063 gauge as specified) or PAC-CLAD steel (24 gauge or 22 gauge as specified). A 35-year non-prorated finish warranty can be supplied covering finish performance. Vinyl masking is recommended on all fabrication applications where extra handling is expected.  NOTE: The strippable film must be removed immediately after installation.

Installation
Tite-Loc Plus panels are intended for use in architectural and structural roofing. Substrates may include 5/8” (min.) plywood,  nailboard insulation or equal with an underlayment of ice and water shield applied horizontally from eave to ridge. Other substrates may include metal decking, purlins or rigid insulation in conjunction with bearing plates. A minimum 1/2:12 pitch is required. Contact Petersen for further assistance with projects details.

For coastal applications, aluminum panels along with stainless steel clips must be used for finish warranty. Consult a local architect/engineer for compliance with local codes and conditions.

Tite-Loc/Tite-Loc Plus Panels
Tite-Loc and Tite-Loc Plus panels are factory-formed to length and field-seamed to a 90° lock (Tite-Loc) or a 180° lock (Tite-Loc Plus). The panels have been designed for application over a wide variety of substrates on roof slopes as low as 1/2:12 pitch. Available in 12”, 16” and 18” widths, Tite-Loc and Tite-Loc Plus panels can be produced in 22 and 24 gauge steel or .032 and .040 aluminum.

Seaming
Tite-Loc and Tite-Loc Plus panels require the use of mechanical seamers. When seaming panels on slopes greater than 6:12, caution must be exercised to prevent seamer slippage and resulting finish scratches that may void the warranty. Seamers are available along with hand crimpers and other tools through D.I. Roof Seamers, which is the only supplier of this equipment approved by Petersen Aluminum. For details and rental information Click Here.

Metal Roofing - How to install Tite-Loc Plus Standing Seam Panel

Tite-Loc Plus Smooth Panel
Smooth Panel (Standard)
zoom_in
Tite-Loc Plus with Striations
With Striations (Optional)
zoom_in
Tite-Loc Plus Striations with Pencil Ribs
Striations w/ Pencil Ribs (Optional)
zoom_in
Tite-Loc Plus Pencil Ribs
Pencil Ribs (Optional)
zoom_in

layers43 stocked colors (24 gauge steel)
layers16 stocked colors (22 gauge steel)
layers36 stocked colors (.032 aluminum)
layers22 stocked colors (.040 aluminum)
layersGalvalume Plus available
close
close