Tite-Loc Plus Panel

Tite-Loc Plus Panel

  • Herr-Voss corrective leveled
  • Pencil ribs (stiffening beads) and striations are only available by request
  • 30-year non-prorated finish warranty
  • Maximum factory-produced panel length is 64’ (check w/factory for longer lengths)
  • Weathertightness warranty available

Tite-Loc panels combine structural panel performance with architectural panel aesthetics. Tite-Loc panels are corrective leveled to provide superior panel flatness. A factory-applied sealant bead is applied for additional weather resistance. Maximum panel length is 64’ and minimum panel length is 4’. Consult factory for longer lengths.

Tite-Loc panels feature a 2” leg height that requires mechanical field seaming after installation. Panels have a concealed-fastener floating clip system designed to allow for thermal expansion/contraction.



All flashing and trim shall be fabricated by manufacturer or qualified fabricator. Flashing shall be PAC-CLAD aluminum (.032 – .063 gauge as specified) or PAC-CLAD steel (24 gauge or 22 gauge as specified). A 30-year non-prorated finish warranty can be supplied covering finish performance. Vinyl masking is recommended on all fabrication applications where extra handling is expected. NOTE: The strippable film must be removed immediately after installation.



Tite-Loc panels are intended for use in architectural and structural roofing. Substrates may include 5/8” (min.) plywood, nailboard insulation or equal with an underlayment of ice and water shield or 30# (min.) roofing felt applied horizontally from eave to ridge. Other substrates may include metal decking, purlins or rigid insulation in conjunction with bearing plates.

A minimum 1/2:12 pitch is required. Contact Petersen Aluminum for further assistance with projects details.
For coastal applications, aluminum panels along with stainless steel clips must be used for finish warranty. Consult a local architect/engineer for compliance with local codes and conditions.


Tite-Loc Plus Roofing Panels

Tite-Loc Plus panels are factory-formed to length and field-seamed to a 180˚ lock (Tite-Loc Plus). The panels have been designed for application over a wide variety of substrates on roof slopes as low as 1/2:12 pitch. Available in 12”, 16” and 18” widths, Tite-Loc and Tite-Loc Plus panels can be produced in 22 and 24 gauge steel or .032 and .040 aluminum.



The Tite-Loc Plus seamer runs in one direction. Tite-Loc Plus panels should be installed from left to right to ensure the seamer travels down slope. The seamer will not travel up slope on a roof pitch greater than 4:12.



  • 38 stocked metal colors (24 gauge steel)
  • 15 stocked metal colors (22 gauge steel)
  • 36 stocked metal colors (.032 aluminum)
  • 20 stocked metal colors (.040 aluminum)
  • Galvalume Plus available

Tite-Loc Plus Installation

PDF Drawings

CAD Drawings



Panel Conditions

Recycle Content


Snap-Clad Panel
Tite-Loc Panel
Tite-Loc Plus Panel
Tite-Loc HS Panel
Snap-On Standing Seam Panel
High Snap-On Standing Seam Panel
Snap-On Batten Panel
Redi-Roof Standing Seam Panel
Redi-Roof Batten Panel
Integral Standing Seam Panel
Integral Batten Panel
ColorGard® Snow Retention System
PAC-150 90° Single Lock
PAC-150 180° Double Lock
M-42 & M-36 Panels
7.2 Panel
1/2″ & 7/8″ Corrugated Panel
R-41 & R-36 Panels
Coil and Flat Sheet
Flashing and Trim
Custom Fabrication
Anodized Aluminum
Copper & Stainless Steel
PAC-750 Soffit
PAC-850 Soffit
Flush/Reveal Soffit
PAC-1000F Column Cover
PAC-1000C Column Cover
PAC-1000R Column Cover
PAC-2000F Column Cover
PAC-2000C Column Cover
PAC-2000R Column Cover
PAC SS Vented Eave & Intake Vent
PAC ECO Vented Fascia
PAC SS Rake Panel & Fascia
PAC SS Ridge Vents
PAC-TITE Angular Fascia
PAC-TITE WT Canted Fascia
PAC-TITE WT Extended Fascia
PAC-LOC Fascia
PAC Snap Edge Fascia
PAC Extended Snap Edge Fascia
PAC-TITE Gold Coping
PAC-Continuous Cleat Coping
Precision Series Wall Panels
Composite Wall Panels
Flush/Reveal Wall Panels