For information on our Privacy & Cookie Policy, please click here.
Reveal Wall Panels
Flush & Reveal Wall PanelsReveal panels are designed for wall, fascia, and soffit applications, offering a flat appearance with optional pencil ribs for longer panels. Installed over a solid substrate or framing sections, they feature factory-formed lengths and concealed fastening clips for enhanced wind resistance. Petersen’s PAC-CLAD panels include precision leveling, durable trim options, and a 30-year finish warranty.
Case Studies
Documents
PDF Drawings
CAD Drawings
Testing
BIM
Green
Recycle Content
Warranties
Features
Leveled for flatness
Available with up to two pencil ribs
Rounded interlock leg provides improved flush fit
35-year non-prorated finish warranty
Panel lengths from 4' to 25’
Optional concealed clips are available for added wind resistance when needed (clips were tested only on the 12" panel but can be used on all widths)
Overview
Reveal panels are designed for wall, fascia and soffit applications where a flat appearance is desired. A rounded interlock leg and concealed fastening system improves aesthetics while providing additional strength. Panels are factory-formed to length to minimize field cutting. Maximum panel length is 25’ and minimum panel length is 4’.
Pencil ribs
The Reveal panels are available with optional pencil ribs. Pencil ribs are recommended for longer panel lengths. One or two ribs are available.
Installation
Reveal panels shall be installed over a solid substrate with appropriate ice and water shield, or in limited applications over framing sections. When used in a windscreen application, panels must be fastened (stitched) through side joints. Consult a local architect/engineer for requirements of local codes and conditions.
Leveling
Petersen’s Reveal panels are formed on precision roll-forming equipment that includes levelers. Leveling removes typical metal conditions including coil set, crowning and edge wave. Leveling is available at no extra charge.
Trim
All flashing and trim shall be fabricated by manufacturer or qualified fabricator. Flashing shall be PAC-CLAD aluminum (.032 – .063 gauge as specified) or PAC-CLAD steel (24 gauge or 22 gauge as specified). A 30-year non-prorated finish warranty can be supplied covering finish performance. Vinyl masking is recommended on all fabrication applications where extra handling is expected.
Optional clip
An optional patented concealed fastening clip is available to raise a panel assembly’s wind resistance performance level. The optional clip has been designed and tested to resist disengagement during high-wind events, but only for the 12-inch panel; consult Petersen factory rep for other widths.
Made from 24 gauge stainless steel, the clip is designed for use with PAC-CLAD Reveal panels. Clips should be installed at the desired spacing per the product load table for the wind resistance requirements of the project.
The optional concealed clip, which is not visible when the installation is complete, is ideal for installations with higher wind-loading requirements that cannot be met without the clip. The clip can be installed on all substrate materials. The clip has passed multiple performance tests and earned Florida Product Approval. The clips are not to be used to reduce oil canning but rather to strengthen the panel in high-wind applications.
NOTE: Consult with Petersen rep or nearest manufacturing facility before specifying this clip.
Note: Oil canning is not a cause for rejection.
Installation
Metal Roofing - Reveal Panel Concealed Clip
Illustration
Materials
48 stocked colors (24 gauge steel)
17 stocked colors (22 gauge steel)
34 stocked colors (.032 aluminum)
26 stocked colors (.040 aluminum)
Galvalume Plus available
Leveled for flatness
Available with up to two pencil ribs
Rounded interlock leg provides improved flush fit
35-year non-prorated finish warranty
Panel lengths from 4' to 25’
Optional concealed clips are available for added wind resistance when needed (clips were tested only on the 12" panel but can be used on all widths)
Reveal panels are designed for wall, fascia and soffit applications where a flat appearance is desired. A rounded interlock leg and concealed fastening system improves aesthetics while providing additional strength. Panels are factory-formed to length to minimize field cutting. Maximum panel length is 25’ and minimum panel length is 4’.
Pencil ribs
The Reveal panels are available with optional pencil ribs. Pencil ribs are recommended for longer panel lengths. One or two ribs are available.
Installation
Reveal panels shall be installed over a solid substrate with appropriate ice and water shield, or in limited applications over framing sections. When used in a windscreen application, panels must be fastened (stitched) through side joints. Consult a local architect/engineer for requirements of local codes and conditions.
Leveling
Petersen’s Reveal panels are formed on precision roll-forming equipment that includes levelers. Leveling removes typical metal conditions including coil set, crowning and edge wave. Leveling is available at no extra charge.
Trim
All flashing and trim shall be fabricated by manufacturer or qualified fabricator. Flashing shall be PAC-CLAD aluminum (.032 – .063 gauge as specified) or PAC-CLAD steel (24 gauge or 22 gauge as specified). A 30-year non-prorated finish warranty can be supplied covering finish performance. Vinyl masking is recommended on all fabrication applications where extra handling is expected.
Optional clip
An optional patented concealed fastening clip is available to raise a panel assembly’s wind resistance performance level. The optional clip has been designed and tested to resist disengagement during high-wind events, but only for the 12-inch panel; consult Petersen factory rep for other widths.
Made from 24 gauge stainless steel, the clip is designed for use with PAC-CLAD Reveal panels. Clips should be installed at the desired spacing per the product load table for the wind resistance requirements of the project.
The optional concealed clip, which is not visible when the installation is complete, is ideal for installations with higher wind-loading requirements that cannot be met without the clip. The clip can be installed on all substrate materials. The clip has passed multiple performance tests and earned Florida Product Approval. The clips are not to be used to reduce oil canning but rather to strengthen the panel in high-wind applications.
NOTE: Consult with Petersen rep or nearest manufacturing facility before specifying this clip.
Note: Oil canning is not a cause for rejection.
Metal Roofing - Reveal Panel Concealed Clip
48 stocked colors (24 gauge steel)
17 stocked colors (22 gauge steel)
34 stocked colors (.032 aluminum)
26 stocked colors (.040 aluminum)
Galvalume Plus available